0
Kenneth
How to get belkin n600 configured?
0 Subscribers
Submit Answer
1 Answers
Best Answer
0
follow these steps for setup of belkin n600 -
- Open the default address http://192.168.2.1(your IP address could be different).
Normally Belkin ship routers with no username or password. If there is a username it’s “admin”.
3. Click DNS on the left side.
4. You might be asked for password again – leave blank if you have no password.
5. Uncheck Automatic from ISP.
6. Enter 185.37.37.37 and 185.37.39.39 in the DNS fields.
7. Click Apply Changes.
8. Restart router and connected devices.
Replying as
Submit
Connect your computer to the modem using an ethernet cable without the router installed.
Verify if your computer is getting an internet connection by accessing a website.
connect extender with computer.
Observe the light of your router located at the upper panel of the device. Wait for a few minutes until the light turns solid blue.
Open a web browser and enter 192.168.2.1
Let’s connect to the Internet. page, tap Detect my connection.
: By default, the Belkin router already has the wireless settings setup. These can be found at the bottom of the router.
Extender will then verify your Network Name and Password. Once done, click
For belkin setup first place your router next to the modem.
Connect your Router’s Ethernet cable to your modem’s Ethernet
port (on the back of your modem). This port might be labeled
differently on your particular modem. If you are adding a
Router for the first time, this port may be connected to your
computer by an Ethernet cable. It is OK to disconnect your
computer and plug the Router into the modem instead.
Plug the Router’s power supply into a wall outlet.
In your browser, type “http://router” (you do not need to type
in anything else such as “www”). Then press the Enter key. If
you’re still having trouble running the manual setup option, type
“192.168.2.1” in your browser (you do not need to type in anything
else such as “http://” or “www”). Then press the Enter key.
Router setup page will be open follow the step and complete the setup.
Set Up Your Range Extender Wirelessly
Step 1
Choose an outlet near the edge of your network’s Wi-Fi coverage.
Step 2
Plug in your N600 DB Range Extender.
4
GETTING STARTED
Step 3
Connect your computer to the “Belkin.setup” wireless network.
Make sure nothing is plugged into your Ethernet port.
On Windows Vista or Windows 7, please check the option
“Connect Automatically” when you select the network.
Belkin.setup
12:00 PM
Search for “Belkin.setup” and connect.
5
GETTING STARTED
Step 4
Visit “http://Belkin.range” and follow the on-screen instructions.
http://Belkin.range
6
GETTING STARTED
Wired Setup
Step 1: Connect the Range Extender to your computer
using an Ethernet cable (Ethernet cable not included).
Step 2: Plug the Range Extender into a wall
socket or other power sources.
Step 3: On your computer, turn off Wi-Fi.
Step 4: Use your favorite browser to visit http://Belkin.
range and follow the instructions that appear there.
Step 5: After your setup is complete, please turn on Wi-Fi.
Set Up Your Range Extender Wirelessly
Step 1
Choose an outlet near the edge of your network’s Wi-Fi coverage.
Step 2
Plug in your N600 DB Range Extender.
Step 3
Connect your computer to the “Belkin.setup” wireless network.
Make sure nothing is plugged into your Ethernet port.
On Windows Vista or Windows 7, please check the option
“Connect Automatically” when you select the network.
Belkin.setup
Search for “Belkin.setup” and connect.
Step 4
Visit “http://Belkin.range” and follow the on-screen instructions.
http://Belkin.range
Wired Setup
Step 1: Connect the Range Extender to your computer
using an Ethernet cable (Ethernet cable not included).
Step 2: Plug the Range Extender into a wall
socket or other power sources.
Step 3: On your computer, turn off Wi-Fi.
Step 4: Use your favorite browser to visit http://Belkin.
range and follow the instructions that appear there.
Step 5: After your setup is complete, please turn on Wi-Fi.
In this case, you need to follow below-mentioned steps-
>first of all if you made any changes on it you need to reset your Belkin N600 Range Extender by pressing the Reset button for 20 seconds(while it’s powered on).
>Once the Extender lights stop flashing then you can easily reconfigure it simply by performing WPS Method on it.
> To do WPS process you need to press the WPS button of your home router for 3 seconds and then within 1 minute, you need to press the same WPS button of your Belkin Extender for 3 seconds.
> Once you find that the lights of the extender are solid/stable, you can connect to its network using the router’s WiFi password with any of your wireless devices and then try to go online so that you come to know its working fine.
*If you still face any kind of trouble with your Router or Extender do write us back so that we can help you accordingly.
How to setup an Belkin N600 DB Extender?
For new Belkin N600 DB Extender.
Just press the WPS on your router/modem first for 1-2 seconds, then press the WPS on Belkin N600 DB Extender for 3-5 seconds.
Now wait for 2 minutes.
The difference in light color and pattern will confirm its connection.
For Used/ old Extender: If its an used Belkin N600 DB Extender then first reset it using a paper clip to press the reset button in a tiny hole for 30 seconds.
Now its brand new, or by default one.
Wait for 2 minutes after reset then proceed further as setup New Extender.
Its now extending your home network with same password as of your home wifi.
Note:
1. During setup, make sure that the Belkin N600 DB Extender is placed within 7-10 feet from Router, at the time of setup, or in the same room.
2. Two minutes patience is the Critical Time that make the difference between success and failure in Setup.
3. Best of luck