Arlo setup

3 comments

• a. Connect the base station to your
  router using an Ethernet cable.

  b. Connect the base station AC
  adapter to your base station and
  plug it in.

  c. Turn the base station on by
  pressing the On/Off button.

  The Power LED and Internet LED on
  the front of the base station light
  green in about two minutes.

  In Computers use a web browser. Use https://arlo.netgear.com as the URL and then use your credentials to log in or sign up and follow the instruction.

  Reply

• Connect Your Base Station to the Internet
  The base station connects to your home network and allows you to view your
  camera streams from anywhere.
  To connect your base station to the Internet:
  1. Connect the base station to your router using an Ethernet cable.
  2. Connect the AC adapter to the base station.
  3. Plug the AC adapter into an electrical outlet.
  4. If your base station includes an On-Off button on the back, press the button.
  The Power LED and Internet LED light green in about two minutes.
  Your base station is set up.
  Get an Account
  #To set up an Arlo account:
  1. Tap the Arlo icon on your mobile device.
  If you are using a computer, enter arlo.netgear.com in the address bar of a
  browser.
  If you are using a mobile device that supports a Touch ID fingerprint identity
  sensor, you are prompted to enable Touch ID or skip.
  2. To use Touch ID, tap Enable Touch ID.
  3. Tap or click New to Arlo?.
  4. Select Arlo (Wire-Free).
  The app discovers your device.
  5. Select your base station’s serial number from the menu.
  6. Complete the required fields for account setup.
  7. Tap or click Continue.
  8. Select a subscription plan.
  Insert Batteries Into Your Cameras
  We recommend that you use the batteries supplied by NETGEAR, or high-quality
  batteries from other established, well-known manufacturers such as Panasonic®,
  Energizer®, or Duracell®, with your Arlo cameras.
  # To insert batteries into your cameras:
  1. Slide and hold the latch on the bottom of the camera.
  2. Slide the battery door back and lift it to open the battery compartment.
  3. Insert two batteries near the back of the camera. Pay careful attention to the
  orientation of the batteries when you insert them.
  4. Insert two batteries near the compartment hinge. Pay careful attention to the
  orientation of the batteries when you insert them.
  5. Close the battery door.
  Sync Your Cameras With the Base Station
  #To sync your cameras:
  1. Bring the camera within 1 to 3 feet (30 to 100 centimeters) of the base station.
  2. Press the Sync button on the base station for about two seconds and then
  release the button.
  3. Wait for the sync status LED on the base station to light green.
  4. Press the Sync button on top of the camera for about two seconds and then
  release the button.
  A blue LED on the camera blinks slowly when the sync process starts. The blue
  LED blinks rapidly to confirm sync.
  After the camera syncs, the Power LED on the base station might start blinking.
  This indicates that the camera’s firmware is updating.
  5. Repeat for each camera.
  Add a Camera From Another Arlo Account
  # To add a camera from another Arlo account:
  1. Tap the Arlo icon on your mobile device.
  If you are using a computer, enter arlo.netgear.com in the address bar of a
  browser.
  The Devices page displays.
  2. Log in to the old Arlo account.
  3. Tap or click Settings > My Devices.
  A list of devices including the base station and cameras displays.
  4. Tap or click the camera.
  The settings for the camera display.
  5. Scroll down and tap or click Remove Device.
  The camera is removed from your account.
  6. Log out of the Arlo app.
  7. Sync the camera to the base station.

  Reply

• Make sure before connecting you have the batteries in the arlo cameras.
  First Connect your base station to the router for internet connection with Ethernet cable.
  Plug the adapter for the base station in the wall.
  Press the Power button of the base station you will see power and internet light green in 2 minutes
  Your base station is setup.

  Now place the camera 3 feets from the base station.
  Press the Sync button on the top of the base station for about two seconds and then release the button.
  Wait till the light for the sync is Green.
  Then Press the Sync button on top of the camera
  The Blue light on camera will slowly blinks.Then LED blinks rapidly to confirm syncing.
  Now the camera is ready to go you can view it in your Arlo app on you device.
  The LED blinks amber if the sync is not successful. You must repeat the sync
  process again for each camera.

  Thank You

  Reply