0
kimmbeckwith
how to setup my netgear extender ac750 ex6100v2?
0 Subscribers
Submit Answer
0 Answers
To connect Netgear extender ac750 ex6100v2 please follow these simple steps:-
1. Set the Access Point/Extender switch to Extender.
2. Place your extender in the same room as your WiFi router.
Proximity to the WiFi router is required only during the initial setup process.
3. Plug the extender into an electrical outlet.
Wait for the Power LED to light green. This might take up to 100 seconds. If the
Power LED does not light, press the Power On/Off button on side of the extender.
Connect to an Existing WiFi Network
To extend the range of your WiFi network, you must connect the extender to your existing
WiFi network. You can do this in one of two ways:
1. Connect with WPS.
2. Connect with the NETGEAR installation assistant.
CONNECT WITH WPS
Wi-Fi Protected Setup (WPS) lets you join a secure WiFi network without typing the network
name and password. (PLEASE NOTE: WPS does not support WEP network security IF YOUR ROUTER IS USING WEP SECURITY PLEASE CHANGE IT TO WPA2-PSK OR HIGHER)
To use WPS to connect the extender to your WiFi router:
1. Press the WPS button on the extender.
The WPS LED blinks.
2. Within two minutes, press the WPS button on your router or access point.
The WPS LED on the extender lights solid green, the Router Link LED lights, and
the extender connects to your existing WiFi network.
If the Router Link LED does not light, try again.
3. If your WiFi router supports the 5 GHz band, repeat Steps 1 and 2 to connect the extender
to the 5 GHz band.
4. Unplug the extender and move it to a new location that is about halfway between your router
and the area with a poor router WiFi signal.
The location that you choose must be within the range of your existing WiFi router
network.
5. Plug the extender into an electrical outlet and wait for the Power LED to light green.
6. Use the Router Link LED to help you choose a spot where the extender-to-router
the connection is optimal.
7. If the Router Link LED does not light amber or green, plug the extender into an outlet closer
to the router and try again.
Keep moving the extender to outlets closer to the router until the Router Link LED lights
amber or green.
8. On your WiFi-enabled computer or mobile device, find and connect to the new extender
WiFi network.
The extender creates two new extender WiFi networks. The extender’s new WiFi network
names are based on your existing WiFi network name, with _2GEXT and _5GEXT at the
ends of the names.
For example:
• Existing WiFi network name. MyNetworkName
• New extender network names. MyNetworkName_2GEXT and
MyNetworkName_5GEXT
Use the same WiFi password that you use for your WiFi router.
9. Test the extender WiFi range by moving your WiFi-enabled computer or mobile device to the
area with a poor router WiFi signal:
a. Leave your WiFi-enabled computer or mobile device in the area with a poor router
WiFi signal and return to the extender.
b. Check the Client Link LED on the extender:
• If the Client Link LED is solid green or amber, your extender WiFi network reaches
the area with a poor router WiFi signal and your network setup is complete.
• If the Client Link LED is red, your extender WiFi network does not reach the area
with a poor router WiFi signal.
You must move the WiFi-enabled computer or mobile device closer to the
extender until the Client Link LED turns solid green or amber.
Connect With the NETGEAR Installation Assistant
To connect with the NETGEAR installation assistant:
1. Use a WiFi network manager on a WiFi-enabled computer or mobile device to find and
connect to the extender WiFi network EX6100_NETGEAR_2EXT.
After the connection with the WiFi-enabled computer or mobile device is established, the
Client Link LED lights.
2. Launch a web browser.
3. Enter http://www.mywifiext.net in the address field of the browser.
The New Extender Setup page displays.
4. Click the NEW EXTENDER SETUP button.
5. Complete the fields on the page and click the NEXT button.
6. Verify that the Access Point/Extender switch is set to Extender and click the
CONTINUE button.
7. Select a WiFi network to extend and click the NEXT button.
Get Started
13
AC750 WiFi Range Extender
If you do not want to extend both WiFi bands, clear the 2.4 GHz WiFi Networks or the
5 GHz WiFi Networks check box.
8. In the Password (Network Key) field, type the existing WiFi network password (also called
passphrase or security key) and click the NEXT button.
9. Set the network name (SSID) and password for your new extender WiFi network and click
the NEXT button.
Note: We recommend that you use a network name (SSID) for your extender
that is different from the SSID that your router uses.
Wait for the page to display a list of available extender WiFi networks, which might take
up to one minute.
10. Connect the WiFi-enabled computer or mobile device to the new extender WiFi network
using the extender SSID and password that you created in Step 9.
11. Make sure that your WiFi-enabled computer or mobile device is connected before you click
the CONTINUE button.
12. Click the CONTIINUE button.
A message displays confirming that the extender is connected to the new extender WiFi
network.
13. Click the NEXT button.
The registration page displays.
14. Complete the registration fields and click the FINISH button to complete the setup.
If you do not want to register your extender, click the Skip Registration link. Note that
you must register your extender before you can use NETGEAR telephone support.
The Status page displays.
15. Unplug the extender and move it to a new location that is about halfway between your router
and the area with a poor router WiFi signal.
The location that you choose must be within the range of your existing WiFi router
network.
TO CONNECT YOUR NETGEAR EX6150V2 EXTENDER YOU NEED TO FOLLOW THESE STEPS
1. CONNECT YOUR EXTENDER IN A DIRECT WALL SOCKET.
2. PRESS WPS BUTTON ON YOUR EXTENDER FOR 3-5 SECONDS.
3.PRESS WPS BUTTON ON YOUR ROUTER (YOU CAN DO IT BY ACCESSING ROUTER MAIN PAGE ALSO).
4.IT WILL BE CONNECTED TO YOUR ROUTERS NETWORK.
5.YOU WILL SE YOUR NETWORK NAME WITH EXT AFFIXED IN IT.
6.CONNECT TO THE SAME NETWORK .
7. IT WILL OPEN A SETUP WIZARD FOR YOU.
8.FOLLOW THE STEPS OF WIZARD AND YOU ARE GOOD TO GO NOW.
(IF PROBLEM STILL PERSISTS YOU CAN RESET YOUR DEVICE.)
FOR ANY QUESTION & QUERY FEEL FREE TO CALL US ON 1-800-603-4024
To connect Netgear extender ac750 ex6100v2 please follow these simple steps:-
1. Set the Access Point/Extender switch to Extender.
2. Place your extender in the same room as your WiFi router.
Proximity to the WiFi router is required only during the initial setup process.
3. Plug the extender into an electrical outlet.
Wait for the Power LED to light green. This might take up to 100 seconds. If the
Power LED does not light, press the Power On/Off button on side of the extender.
Connect to an Existing WiFi Network
To extend the range of your WiFi network, you must connect the extender to your existing
WiFi network. You can do this in one of two ways:
1. Connect with WPS.
2. Connect with the NETGEAR installation assistant.
CONNECT WITH WPS
Wi-Fi Protected Setup (WPS) lets you join a secure WiFi network without typing the network
name and password. (PLEASE NOTE: WPS does not support WEP network security IF YOUR ROUTER IS USING WEP SECURITY PLEASE CHANGE IT TO WPA2-PSK OR HIGHER)
To use WPS to connect the extender to your WiFi router:
1. Press the WPS button on the extender.
The WPS LED blinks.
2. Within two minutes, press the WPS button on your router or access point.
The WPS LED on the extender lights solid green, the Router Link LED lights, and
the extender connects to your existing WiFi network.
If the Router Link LED does not light, try again.
3. If your WiFi router supports the 5 GHz band, repeat Steps 1 and 2 to connect the extender
to the 5 GHz band.
4. Unplug the extender and move it to a new location that is about halfway between your router
and the area with a poor router WiFi signal.
The location that you choose must be within the range of your existing WiFi router
network.
5. Plug the extender into an electrical outlet and wait for the Power LED to light green.
6. Use the Router Link LED to help you choose a spot where the extender-to-router
the connection is optimal.
7. If the Router Link LED does not light amber or green, plug the extender into an outlet closer
to the router and try again.
Keep moving the extender to outlets closer to the router until the Router Link LED lights
amber or green.
8. On your WiFi-enabled computer or mobile device, find and connect to the new extender
WiFi network.
The extender creates two new extender WiFi networks. The extender’s new WiFi network
names are based on your existing WiFi network name, with _2GEXT and _5GEXT at the
ends of the names.
For example:
• Existing WiFi network name. MyNetworkName
• New extender network names. MyNetworkName_2GEXT and
MyNetworkName_5GEXT
Use the same WiFi password that you use for your WiFi router.
9. Test the extender WiFi range by moving your WiFi-enabled computer or mobile device to the
area with a poor router WiFi signal:
a. Leave your WiFi-enabled computer or mobile device in the area with a poor router
WiFi signal and return to the extender.
b. Check the Client Link LED on the extender:
• If the Client Link LED is solid green or amber, your extender WiFi network reaches
the area with a poor router WiFi signal and your network setup is complete.
• If the Client Link LED is red, your extender WiFi network does not reach the area
with a poor router WiFi signal.
You must move the WiFi-enabled computer or mobile device closer to the
extender until the Client Link LED turns solid green or amber.
Connect With the NETGEAR Installation Assistant
To connect with the NETGEAR installation assistant:
1. Use a WiFi network manager on a WiFi-enabled computer or mobile device to find and
connect to the extender WiFi network EX6100_NETGEAR_2EXT.
After the connection with the WiFi-enabled computer or mobile device is established, the
Client Link LED lights.
2. Launch a web browser.
3. Enter http://www.mywifiext.net in the address field of the browser.
The New Extender Setup page displays.
4. Click the NEW EXTENDER SETUP button.
5. Complete the fields on the page and click the NEXT button.
6. Verify that the Access Point/Extender switch is set to Extender and click the
CONTINUE button.
7. Select a WiFi network to extend and click the NEXT button.
Get Started
13
AC750 WiFi Range Extender
If you do not want to extend both WiFi bands, clear the 2.4 GHz WiFi Networks or the
5 GHz WiFi Networks check box.
8. In the Password (Network Key) field, type the existing WiFi network password (also called
passphrase or security key) and click the NEXT button.
9. Set the network name (SSID) and password for your new extender WiFi network and click
the NEXT button.
Note: We recommend that you use a network name (SSID) for your extender
that is different from the SSID that your router uses.
Wait for the page to display a list of available extender WiFi networks, which might take
up to one minute.
10. Connect the WiFi-enabled computer or mobile device to the new extender WiFi network
using the extender SSID and password that you created in Step 9.
11. Make sure that your WiFi-enabled computer or mobile device is connected before you click
the CONTINUE button.
12. Click the CONTIINUE button.
A message displays confirming that the extender is connected to the new extender WiFi
network.
13. Click the NEXT button.
The registration page displays.
14. Complete the registration fields and click the FINISH button to complete the setup.
If you do not want to register your extender, click the Skip Registration link. Note that
you must register your extender before you can use NETGEAR telephone support.
The Status page displays.
15. Unplug the extender and move it to a new location that is about halfway between your router
and the area with a poor router WiFi signal.
The location that you choose must be within the range of your existing WiFi router
network.