0
Ted Schlemovitz
how to re-setup a TPlink Extender?
0 Subscribers
Submit Answer
1 Answers
Best Answer
0
IN ORDER TO RESETÂ THE TP LINK RANGE EXTENDER WE HAVE TO FOLLOW THE FOLLOWING STEPS
PRESS THE RESET BUTTON ON THE RANGE EXTENDER FOR 30 SECONDS AND THEN WAIT FOR 1 MINUTE
IN ORDER TO CONFIGURE THE RANGE EXTENDER WE NEED TO FOLLOW THE FOLLOWING STEPS
PLUG YOUR RANGE EXTENDER NEAR TO THE ROUTER
PRESS THE WPS BUTTON ON THE RANGE EXTENDER FORÂ 3-4Â SECONDSÂ AND THE RELEASE
THEN PRESS THE WPS BUTTON ON THE ROUTER FOR 3-4Â SECONDS
ONCE YOU SEE THE LIGHT STOPS FLASHING ON THE RANGE EXTENDER
IT MEANS THAT EXTENDER IS SETUP NOW
IN THIS WAY WE CAN RESET THE RANGE EXTENDER
Replying as
Submit
In order to re-setup a extender, please follow the steps below:
Reset the extender, Press and hold the reset button down for 30 seconds and then wait for atleast 1 minute.
In order to configure the range extender you need to follow the instructions below:
> plug in your extender near to the router for the initial setup within 10 feets
> Press the WPS button on the router for 3 -4 seconds and then on the Extender for 3- 4 Seconds
> Once you see the light stopped flashing on the extender it means the extender is setup now
Step 2
> Connect your computer wireless to the extended network
> pull up browser and at the very top type in 192.168.0.254 or 192.168.1.254
> You will get through a login window default username: admin and the Password : admin
> click on quick setup and Continue , Follow the instructions to complete the setup
.CONNECT YOUR EXTENDER IN A DIRECT WALL SOCKET.
2. PRESS WPS BUTTON ON YOUR EXTENDER FOR 3-5 SECONDS.
3.PRESS WPS BUTTON ON YOUR ROUTER AND YOU WILL SEE LIGHTS STARTS BLINKING ON YOUR EXTENDER.
4.IT WILL BE CONNECTED TO YOUR ROUTERS NETWORK ONCE THE LIGHT WILL BE SOLID.
5.NOW ENTER THE ADDRESS FOR YOUR EXTENDER SET UP.
6.LOGIN WITH DEFAULT CREDENTIALS THERE.
7. IT WILL OPEN A SETUP WIZARD FOR YOU.
8.FOLLOW THE STEPS OF WIZARD AND YOU ARE GOOD TO GO NOW.
To resetup your Tp link extender first reset your extender with the paper clip and then follow these steps:-
1.Plug your Range Extender into a power outlet near your main Router.
2.Push the WPS button on your main Router first, then immediately push the WPS button on your Range Extender.
3. After you have pushed WPS button of your Router, you need to push WPS button of your Range Extender within 2 minutes. .
4.After pushing the WPS button of your Router, your Router WPS LED should blink. If your Router WPS LED doesn’t blink, it means you need to push the WPS button again until the WPS LED of your Router blinks. The same reason is also suitable for RE product. After pushing the WPS button of your Range Extender, the WPS light of your Range Extender should blink. If not, push again.
5.The WPS process will last 2 minutes. You can wait 2 minutes, and then check the wireless signal LED of your Range Extender.
5. After 2 minutes, if the wireless signal LED of your Range Extender is still off, it means the WPS process fails. You may need to try one more or several more times of WPS operation, and repeat the steps above.
6. At last, you can put your Range Extender in a proper place where you want to extend the wireless network’s coverage, and enjoy the extended wireless network. No need to repeat the process. Once it’s done, it will connect automatically every time you plug it back in.
For any help feel free to call us back on 1-800-603-4024.