Answers ( 6 )

  1. Please briefly explain why you feel this answer should be reported .

    Report
    Cancel

    TO SET UP YOUR TP LINK ROUTER YOU NEED TO FOLLOW THESE STEPS:
    1. PLUG IN YOUR ROUTER TO A WALL SOCKET.
    2. CONNECT AN ETHERNET CABLE FROM YOUR MODEM TO INTERNET PORT OF YOUR ROUTER.
    3. CONNECT ANOTHER ETHERNET CABLE FROM PORT NO-4 OF YOUR ROUTER TO YOUR COMPUTER.
    4. OPEN RUN WINDOW AND TYPE CMD FOR ACCESSING LINKSYS ROUTER WRT54G V8.2.
    5. THEN ON CMD WINDOW TYPE IPCONFIG IT WILL SHOW YOU NETWORK STATISTICS.
    6. THEN OPEN A BROWSER AND TYPE DEFAULT GATEWAY IN ADDRESS BAR HIT ENTERS.
    7. WHEN YOU WILL HIT ENTER KEY THERE WILL BE A PROMPT ASKING USERNAME AND PASSWORD.
    8. DEFAULT USERNAME-admin PASSWORD-password.
    9. IT WILL OPEN A SETUP WIZARD YOU JUST NEED TO FOLLOW STEPS AND ROUTER WILL BE CONNECTED TO NETWORK.
    IF STILL PROBLEM PERSISTS YOU CAN RESET YOUR DEVICE.
    FEEL FREE TO CALL US BACK ON 1-800-603-4024.

    (0)(0)
  2. Shawn white

    Please briefly explain why you feel this answer should be reported .

    Report
    Cancel

    CONNECT YOUR EXTENDER IN A DIRECT WALL SOCKET.
    2. PRESS WPS BUTTON ON YOUR EXTENDER FOR 3-5 SECONDS.
    3.PRESS WPS BUTTON ON YOUR ROUTER AND YOU WILL SEE LIGHTS STARTS BLINKING ON YOUR EXTENDER.
    4.IT WILL BE CONNECTED TO YOUR ROUTERS NETWORK ONCE THE LIGHT WILL BE SOLID.
    5.NOW ENTER THE ADDRESS FOR YOUR EXTENDER SET UP.
    6.LOGIN WITH DEFAULT CREDENTIALS THERE.
    7. IT WILL OPEN A SETUP WIZARD FOR YOU.
    8.FOLLOW THE STEPS OF WIZARD AND YOU ARE GOOD TO GO NOW.
    (IF PROBLEM STILL PERSISTS YOU CAN RESET YOUR DEVICE.)
    FOR ANY QUESTION & QUERY FEEL FREE TO CALL US ON 1-800-603-4024.

    (0)(0)
  3. Leo

    Please briefly explain why you feel this answer should be reported .

    Report
    Cancel

    TPlink-RE450 extender Setup –
    Plug your extender into power socket . Avoid surge protector /Extensions !
    You need to reset the extender so hold the reset button on extender for 25 seconds and release it.
    1-Connect your device to extender’s network .
    2-Open your Browser.
    3-Type http://tplinkrepeater.net or 192.168.0.250 / 192.168.0.254 in address bar.
    4-You need to login now with default login:-Username-admin /Password-admin.
    5-Setup wizard will guide you through setup.

    (0)(0)
  4. Mark.Tech

    Please briefly explain why you feel this answer should be reported .

    Report
    Cancel

    ROUTER SETUP FOR TP-LINK EXTENDER

    1.PLUG IN THE ROUTER TO THE POWER.
    2.Connect an Ethernet cable from modem to your router’s WAN port.
    3.Connect another cable from router to computer .
    4.Now open your browser and type in the address bar www.tplinkwifi.net .
    5.follow the instructions on the screen.
    6.Once your setup is completed remove the ethernet from computer.

    (0)(0)
  5. Mark.Tech

    Please briefly explain why you feel this answer should be reported .

    Report
    Cancel

    we will try connecting with wps setup.

    •Press the WPS button located at the tp-link extender and do the same on your router, within two minutes, tp-link extender will connect itself with the existing network.
    •Type http://tplinkrepeater.net or 192.168.0.250 in address bar ,if the setup is not working.
    •You will notice that the LED status will be solid green,it means its ready to use.

    (Once your tp-link extender is connected with the existing network you can place the WiFi extender where the dead zones are at your location.)

    call us at 1-800-603-4024 if your are still facing issues.

    (0)(0)
  6. Timothy.Brown

    Please briefly explain why you feel this answer should be reported .

    Report
    Cancel

    In order to configure the range extender you need to follow the instructions below:
    > plug in your extender near to the router for the initial setup within 10 feets
    > Press the WPS button on the router for 3 -4 seconds and then on the Extender for 3- 4 Seconds
    > Once you see the light stopped flashing on the extender it means the extender is setup now
    Step 2
    > Connect your computer wireless to the extended network
    > pull up browser and at the very top type in 192.168.0.254 or 192.168.1.254
    > You will get through a login window default username: admin and the Password : admin
    > click on quick setup and Continue , Follow the instructions to complete the setup

    (0)(0)

Leave an answer

Browse

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>