Leave a reply

5 comments
  • Steps to configure netgear extender:-
    Use a computer to connect to NETGEAR WiFi Extender via Ethernet cable.
    Login to the web user interface of your NETGEAR WiFi Extender using http://myWiFiext.net.
    You will be prompted to enter a username and password.
    Default login credentials are:
    Username: admin
    Password: password
    Note: Username and password are case sensitive.
    Once you have successfully logged in, go to Setup > Wireless Settings.
    Check the value in the Password (Network Key) field under Security Options.
    If the password is not same as your Access Point (AP) password, change it so it matches your Access Point password.
    Click Apply. (Extender and AP password need to match)
    Reconnect your Wi-Fi devices to the NETGEAR WiFi Extender using either the WPS button or manual connection.
    If you still facing any trouble just dial 1-800-603-4024 and get additional from expertise..



    0



  • IN THAT CASE I WILL REQUEST YOU TO RESET THE EXTENDER AND FOLLOW THIS GUIDE TO SETUP THE PAGE AGAIN-

    1.PRESS THE WPS BUTTON ON YOUR ROUTER AND THEN YOU WILL SEE A LIGHT BLINKING ON THE FRONT OF THE ROUTER.
    2.THEN PRESS THE WPS ON YOUR EXTENDER AND YOU WILL SEE A LIGHT BLINKING THERE AS WELL.
    3.NOW YOU WILL SEE THE STABLE POWER LIGHT ON YOUR EXTENDER AFTER TWO MINUTES.
    4.SOLID GREEN MEANS ITS SETUP AND YOU CAN CONNECT YOUR DEVICES.
    5.THE PASSWORD FOR EXTENDERS WIFI WILL BE SAME AS YOUR ROUTER.
    6.ONCE THE EXTENDER IS SETUP OPEN http://myWiFiext.net AND YOU WILL BE ABLE TO LOG IN.



    0



  • You need to follow these steps –

    1.Reset the extender by holding reset pinhole for 20 seconds.
    2.Wait until you see solid green light .
    3.Once its solid connect your device to extender network .
    4.Open your browser and type http://mywifiext.net or 192.168.1.250 .
    5.You will see new extender setup page .Just follow the steps to complete it.



    0



  • Use a computer to connect to NETGEAR WiFi Extender via Ethernet cable.
    Login to the web user interface of your NETGEAR WiFi Extender using http://myWiFiext.net.
    You will be prompted to enter a username and password.
    Default login credentials are:
    Username: admin
    Password: password
    Note: Username and password are case sensitive.
    Once you have successfully logged in, go to Setup > Wireless Settings.
    Check the value in the Password (Network Key) field under Security Options.
    If the password is not same as your Access Point (AP) password, change it so it matches your Access Point password.
    Click Apply. (Extender and AP password need to match)
    Now connect your wifi devices to the extender and go



    0



  • THERE ARE SEVERAL WAYS TO CONNECT YOUR NETGEAR EXTENDER I.E ETHERNET CABLE METHOD ,WPS METHOD AND MANY MORE BUT I AM SHARING WPS METHOD HERE FOR WPS METHOD YOU NEED TO FOLLOW THESE STEPS:-
    1. CONNECT YOUR EXTENDER IN A DIRECT WALL SOCKET NEAR BY YOUR ROUTER FOR SETUP.
    2. PRESS WPS BUTTON ON YOUR EXTENDER FOR 3-5 SECONDS.
    3. PRESS WPS BUTTON ON YOUR ROUTER (YOU CAN DO IT BY ACCESSING ROUTER MAIN PAGE ALSO).
    4. IT WILL BE CONNECTED TO YOUR ROUTERS NETWORK.
    5. YOU WILL SE YOUR NETWORK NAME WITH EXT AFFIXED IN IT.
    6. CONNECT TO THE SAME NETWORK .
    7. IT WILL OPEN A SETUP WIZARD FOR YOU.
    8. FOLLOW THE ON SCREEN INSTRUCTIONS AND YOU ARE GOOD TO GO NOW.
    (IF PROBLEM STILL PERSISTS YOU CAN RESET YOUR DEVICE.)
    FOR ANY QUESTION & QUERY FEEL FREE TO CALL US ON 1-800-603-4024.



    0



Written by Tawnya
Router Categories